research papers\(\def\hfill{\hskip 5em}\def\hfil{\hskip 3em}\def\eqno#1{\hfil {#1}}\)

Journal logoJOURNAL OF
SYNCHROTRON
RADIATION
ISSN: 1600-5775

More are better, but the details matter: combinations of multiple Fresnel zone plates for improved resolution and efficiency in X-ray microscopy

CROSSMARK_Color_square_no_text.svg

aApplied Physics, Northwestern University, Evanston, IL 60208, USA, bAdvanced Photon Source, Argonne National Laboratory, Argonne, IL 60439, USA, cDepartment of Physics and Astronomy, Argonne National Laboratory, Argonne, IL 60439, USA, and dChemistry of Life Processes Institute, Northwestern University, Evanston, IL 60208, USA
*Correspondence e-mail: cjacobsen@anl.gov

Edited by A. Momose, Tohoku University, Japan (Received 12 April 2017; accepted 14 May 2018; online 17 June 2018)

Fresnel zone plates used for X-ray nanofocusing face high-aspect-ratio nanofabrication challenges in combining narrow transverse features (for high spatial resolution) along with extended optical modulation along the X-ray beam direction (to improve efficiency). The stacking of multiple Fresnel zone plates along the beam direction has already been shown to offer improved characteristics of resolution and efficiency when compared with thin single zone plates. Using multislice wave propagation simulation methods, here a number of new schemes for the stacking of multiple Fresnel zone plates are considered. These include consideration of optimal thickness and spacing in the axial direction, and methods to capture a fraction of the light otherwise diffracted into unwanted orders, and instead bring it into the desired first-order focus. The alignment tolerances for stacking multiple Fresnel zone plates are also considered.

1. Introduction

Fresnel zone plates are widely used as the nanofocusing optic in X-ray microscopes (Sakdinawat & Attwood, 2010[Sakdinawat, A. & Attwood, D. (2010). Nat. Photon. 4, 840-848.]; Attwood & Sakdinawat, 2017[Attwood, D. & Sakdinawat, A. (2017). X-rays and Extreme Ultraviolet Radiation, 2nd ed. Cambridge University Press.]). They focus beams or image specimens with a Rayleigh resolution of [\delta_{\rm r}] = 1.22drN/m where drN is the width of the finest outermost zone and m is the diffractive order used for focusing. Their first-order focusing efficiency depends on the refractive index n = [1-\delta-i\beta] of the zone material (Henke et al., 1993[Henke, B. L., Gullikson, E. M. & Davis, J. C. (1993). At. Data Nucl. Data Tables, 54, 181-342.]), with a scalar diffraction efficiency [\varepsilon_{m}] for a zone plate thickness t given by (Kirz, 1974[Kirz, J. (1974). J. Opt. Soc. Am. 64, 301-309.])

[\varepsilon_{m} = {{1}\over{m^{2}\pi^{2}}} \, \big[1+\exp\left(-2\eta\varphi\right) - 2\exp\left(-\eta\varphi\right) \cos{\varphi} \big], \eqno(1)]

where [\varphi] = [2\pi t \delta /\lambda] and

[\eta \,\equiv\, {{\beta}/{\delta}}. \eqno(2)]

The efficiency reaches a maximum at a thickness topt satisfying the condition

[{{2\pi\delta t_{\rm opt}} \over {\lambda}} \simeq \pi - 2\eta \eqno(3)]

or

[t_{\rm opt} \simeq {{\lambda} \over {2\delta}} \, \left( 1-{{2\beta}\over{\pi\delta}}\right), \eqno(4)]

which for gold gives [\varepsilon_{1}] = 8.7% at topt = 98 nm when using 0.5 keV soft X-rays, and [\varepsilon_{1}] = 32.7% at topt = 2.0 µm when using 10 keV hard X-rays. Thus one can see that efficient high-resolution multi-keV X-ray focusing requires the fabrication of high-aspect-ratio structures with narrow zone width drN but large thickness t [see Fig. 1(a)[link]]. There is in fact much progress in fabricating conventional Fresnel zone plates with high aspect ratios (Schneider et al., 1995[Schneider, G., Schliebe, T. & Aschoff, H. (1995). J. Vac. Sci. Technol. B, 13, 2809-2812.]; Spector et al., 1997[Spector, S., Jacobsen, C. & Tennant, D. (1997). J. Vac. Sci. Technol. B, 15, 2872-2876.]; Jefimovs et al., 2007[Jefimovs, K., Vila-Comamala, J., Pilvi, T., Raabe, J., Ritala, M. & David, C. (2007). Phys. Rev. Lett. 99, 264801.]; Werner et al., 2014[Werner, S., Rehbein, S., Guttmann, P. & Schneider, G. (2014). Nano Res. 7, 528-535.]; Chang & Sakdinawat, 2014[Chang, C. & Sakdinawat, A. (2014). Nat. Commun. 5, 4243.]; Mohacsi et al., 2017[Mohacsi, I., Vartiainen, I., Rösner, B., Guizar-Sicairos, M., Guzenko, V. A., McNulty, I., Winarski, R., Holt, M. V. & David, C. (2017). Sci. Rep. 7, 43624.]; Li et al., 2017b[Li, K., Wojcik, M. J., Divan, R., Ocola, L. E., Shi, B., Rosenmann, D. & Jacobsen, C. (2017b). J. Vac. Sci. Technol. B, 35, 06G901.]). However, even if technological limits on high-aspect-ratio nanofabrication were removed, there remain fundamental limits: as zones increase in thickness, they begin to need to be tilted to match the Bragg condition (Maser & Schmahl, 1992[Maser, J. & Schmahl, G. (1992). Opt. Commun. 89, 355-362.]) or even curved to match the converging wave as in a volume hologram (Pennington & Lin, 1965[Pennington, K. S. & Lin, L. H. (1965). Appl. Phys. Lett. 7, 56-57.]; Kogelnik, 1969[Kogelnik, H. (1969). Bell Syst. Tech. J. 48, 2909-2947.]; Goodman, 2005[Goodman, J. W. (2005). Introduction to Fourier Optics. Greenwood Village: Roberts and Company Publishers.]), as shown in Fig. 1(d)[link].

[Figure 1]
Figure 1
Zone plates modulate the phase and magnitude of a transmitted wave so as to direct it to a focus. This can be done in several ways, using magnitude and/or phase modulations on alternating zones of half-wavelength optical path difference to the focus. A simple Fresnel zone plate (a) has an outermost zone width of drN and a thickness t; it applies a constant magnitude reduction or phase shift across each zone, while a blazed zone plate (b) puts a staircase approximation of a phase ramp across the zone. One can stack several thin Fresnel zone plates (c) to manipulate the wave at several locations leading to the focus, or use thicker zones (d) which are individually tilted to meet the Bragg grating condition or even curved in a volume hologram approach to produce the converging wavefield.

An alternative approach to a monolithic three-dimensional optical structure is to stack multiple separate zone plates together. When doing so, one must pay attention to how the separation distances [\Delta z] compare with the depth of focus. The depth of focus (DoF) of a Fresnel zone plate can be expressed as twice the depth resolution [\delta_{z}] or (Wang et al., 2000[Wang, Y., Jacobsen, C., Maser, J. & Osanna, A. (2000). J. Microsc. 197, 80-93.])

[{\rm DoF} = 2\delta_{z} = 4\left[1.22{{\left({\rm{d}}r_{N}\right)^{2}}/{\lambda}}\right]. \eqno(5)]

When multiple zone plates are located well within a depth of focus along the wavefield propagation direction, one can treat the net effect as being due to a zone plate with the combined thickness t as has been demonstrated (Shastri et al., 2001[Shastri, S. D., Maser, J. M., Lai, B. & Tys, J. (2001). Opt. Commun. 197, 9-14.]; Maser et al., 2002[Maser, J., Lai, B. P., Yun, W., Shastri, S. D., Cai, Z., Rodrigues, W., Xu, S. & Trackhtenberg, E. (2002). Proc. SPIE, 4783, 74-81.]; Snigireva et al., 2007[Snigireva, I., Snigirev, A., Kohn, V., Yunkin, V., Grigoriev, M., Kuznetsov, S., Vaughan, G. & Di Michiel, M. (2007). Phys. Status Solidi A, 204, 2817-2823.]; Kagoshima et al., 2011[Kagoshima, Y., Takano, H., Koyama, T., Tsusaka, Y. & Saikubo, A. (2011). Jpn. J. Appl. Phys. 50, 022503.]; Feng et al., 2007[Feng, Y., Feser, M., Lyon, A., Rishton, S., Zeng, X., Chen, S., Sassolini, S. & Yun, W. (2007). J. Vac. Sci. Technol. B, 25, 2004.]; Aristov et al., 2007[Aristov, V. V., Isoyan, A., Kohn, V., Kuyumchyan, A., Shulakov, E., Snigirev, A. A. & Snigireva, I. (2007). Nucl. Instrum. Methods Phys. Res. A, 575, 238-241.]; Mohacsi et al., 2014[Mohacsi, I., Karvinen, P., Vartiainen, I., Guzenko, V. A., Somogyi, A., Kewish, C. M., Mercere, P. & David, C. (2014). J. Synchrotron Rad. 21, 497-501.], 2017[Mohacsi, I., Vartiainen, I., Rösner, B., Guizar-Sicairos, M., Guzenko, V. A., McNulty, I., Winarski, R., Holt, M. V. & David, C. (2017). Sci. Rep. 7, 43624.]; Rehbein et al., 2015[Rehbein, S., Lyon, A., Leung, R., Feser, M. & Schneider, G. (2015). Opt. Express, 23, 11063-11072.]). However, this close proximity is often challenging to achieve in practice, leading to an alternative approach of stacking multiple zone plates with separations larger than [2\delta_{z}] provided each individual zone plate is designed to focus to a common location (Vila-Comamala et al., 2013[Vila-Comamala, J., Wojcik, M., Diaz, A., Guizar-Sicairos, M., Kewish, C. M., Wang, S. & David, C. (2013). J. Synchrotron Rad. 20, 397-404.]; Gleber et al., 2014[Gleber, S. C., Wojcik, M., Liu, J., Roehrig, C., Cummings, M., Vila-Comamala, J., Li, K., Lai, B., Shu, D. & Vogt, S. (2014). Opt. Express, 22, 28142-28153.]). This has been studied within the approximation that each zone plate is optically thin, so that one can apply each zone plate's optical modulation to a wavefield, and then propagate it by a distance of [\Delta z] to the plane of the next zone plate to model the net focusing effect.

In this paper, we look in further detail at the optical properties of multiple stacked Fresnel zone plates. We make use (when necessary) of the multislice propagation technique (Cowley & Moodie, 1957[Cowley, J. M. & Moodie, A. F. (1957). Acta Cryst. 10, 609-619.]) which can replicate (Li et al., 2017a[Li, K., Wojcik, M. & Jacobsen, C. (2017a). Opt. Express, 25, 1831-1846.]) the results of coupled-wave theory which is otherwise required (Maser & Schmahl, 1992[Maser, J. & Schmahl, G. (1992). Opt. Commun. 89, 355-362.]; Schneider, 1997[Schneider, G. (1997). Appl. Phys. Lett. 71, 2242-2244.]; Schneider et al., 2008[Schneider, G., Rehbein, S. & Werner, S. (2008). Modern Developments in X-ray and Neutron Optics, edited by A. Erko, M. Idir, T. Krist and A. G. Michette, pp. 137-171. Springer.]) when studying very high aspect ratio zone plates. We consider for the first time the following features of stacked zone plates:

(i) While previous calculations (Vila-Comamala et al., 2013[Vila-Comamala, J., Wojcik, M., Diaz, A., Guizar-Sicairos, M., Kewish, C. M., Wang, S. & David, C. (2013). J. Synchrotron Rad. 20, 397-404.]) and experiments (Gleber et al., 2014[Gleber, S. C., Wojcik, M., Liu, J., Roehrig, C., Cummings, M., Vila-Comamala, J., Li, K., Lai, B., Shu, D. & Vogt, S. (2014). Opt. Express, 22, 28142-28153.]) considered intermediate distance stacking with zone plates with fixed outermost zone width drN and adjustable diameter d, we consider the three cases of fixed drN, fixed d and fixed zone number N in §2[link].

(ii) We examine in detail the exit wave from the last of a stacked set of Fresnel zone plates, and show in §3[link] that with multiple zone plates one begins to produce an effect like that of blazed zone plates but without the tradeoff of minimum linewidth otherwise required.

(iii) We show in §4[link] that the Talbot effect can be used to understand that there are optimum separation distances between stacked zone plates.

(iv) In §5[link] we consider `complementary' zone plates where the positions of `open' and `filled' zones are reversed in some elements of a stacked combination, and show that this can reduce the effect of sidelobes off of the focus which can be advantageous for applications such as trace-element mapping using X-ray fluorescence.

(v) We consider `refocusing' zone plates in §6[link], where some of the negative or diverging focal-order light from an upstream zone plate is captured and brought back into the positive first-order focus.

In addition to the above, in the supporting information we consider alignment tolerances of stacked zone plates as already discussed in the references cited, but provide more detail on misalignment effects.

2. Selecting multiple zone plate parameters

For larger separation distances between individual zone plates, the relationship between diameter d, outermost zone width drN and zone number N of

[N={{d}/{4{\rm{d}}r_{N}}} \eqno(6)]

and the focal length of

[f=d\,{\rm{d}}r_{N}/\lambda \eqno(7)]

indicate that one has a choice in fixing any one of three parameters in order to adjust the ith zone plate to have a focal length fi so as to focus at the common location. These strategies are as follows:

(i) Fixed outermost zone width drN: in this case, the diameter is adjusted according to di = [\lambda f_{i}/{\rm{d}}r_{N}] and the number of zones is adjusted to Ni = di/(4drN).

(ii) Fixed diameter d: in this case, the outermost zone width is adjusted according to drN,i = [\lambda f_{i}/d] and the number of zones is adjusted to Ni = d/(4drN,i).

(iii) Fixed zone number N: in this case, the diameter is adjusted according to di = [2(N\lambda f_{i})^{1/2}] and the outermost zone width is adjusted to drN,i = [\lambda f_{i}/d_{i}].

While the fixed drN approach has been studied previously (Vila-Comamala et al., 2013[Vila-Comamala, J., Wojcik, M., Diaz, A., Guizar-Sicairos, M., Kewish, C. M., Wang, S. & David, C. (2013). J. Synchrotron Rad. 20, 397-404.]; Gleber et al., 2014[Gleber, S. C., Wojcik, M., Liu, J., Roehrig, C., Cummings, M., Vila-Comamala, J., Li, K., Lai, B., Shu, D. & Vogt, S. (2014). Opt. Express, 22, 28142-28153.]), the fixed d and fixed N approaches have not.

Because many nanofabrication processes have limits on the achievable aspect ratio t/drN, when considering approaches that vary the outermost zone width drN,i we have also chosen to adjust the thickness of the ith zone plate according to

[t_{i} = t_{1}\,{{{\rm{d}}r_{N,i}}\over{{\rm{d}}r_{N,1}}} \eqno(8)]

for the fixed diameter d and fixed zone number N choices. In order to make clear the differences between these strategies, we show in Table 1[link] the parameters that result when four zone plates are used at 10 keV with a very large separation of [\Delta z] = 1 mm between each zone plate.

Table 1
Parameters for nzp = 4 zone plates stacked at a separation distance of [\Delta z] = 1 mm, using the strategies of fixing the diameter d in µm, or the number of zones N, or the outermost zone width drN in nm for the ith zone plate

Under the assumption that a zone plate fabrication process has a limit to achievable aspect ratios t/drN, zone plate thicknesses are also adjusted according to ti = t1drN,i/drN,1 where t1 = 500 nm in this case.

  Fixed d Fixed N Fixed drN
fi (µm) d NI drN,i ti di N drN,i ti di Ni drN t
9074 (i = 1) 45.0 450 25.0 500 45.0 450 25.0 500 45.0 450 25.0 500
8074 (i = 2) 45.0 506 22.2 446 42.4 450 23.6 472 40.0 400 25.0 500
7074 (i = 3) 45.0 577 19.5 390 39.7 450 22.1 442 35.1 351 25.0 500
6074 (i = 4) 45.0 672 16.7 334 36.8 450 20.5 410 30.1 301 25.0 500

To understand the consequences of these different strategies, in Fig. 2[link] we show the efficiency and spatial resolution values that result. The case of fixed diameter d yields the highest efficiency and resolution, even though the downstream zone plates are assumed to have lower thickness ti and thus lower individual diffraction efficiency. In the case of fixed diameter d, the downstream zone plates capture a larger fraction of the zero-order undiffracted light passing through upstream zone plates, and the final zone plate has a smaller outermost zone width drN,i which contributes to a higher spatial resolution. This increase in area more than compensates for the decrease in thickness ti. In contrast to this case, the fixed outermost zone width drN case has the smallest diameter di for the later zone plates. A factor not considered in the efficiency or energy fraction shown in Fig. 2[link] is the spectral bandwidth, which should be limited (Thieme, 1988[Thieme, J. (1988). X-ray Microscopy II, edited by D. Sayre, M. R. Howells, J. Kirz and H. Rarback, Vol. 56 of Springer Series in Optical Sciences, pp. 70-79. Berlin: Springer-Verlag.]) to

[{{\Delta\lambda}/{\lambda}} \,\lesssim\, {{1}/{N}}. \eqno(9)]

In the case of fixed d, the change from N1 = 450 to N4 = 672 zones would reduce the acceptable spectral bandwidth by 33.0% relative to the fixed zone number N case; in the fixed outermost zone width drN case one would not gain from the smaller value of N4 = 301 because the spectral bandwidth would still be limited by N1 = 450. The choice of fixed diameter d or fixed zone number N therefore depends on the degree to which spectral bandwidth acceptance can be controlled, since in many cases zone plate microscopes are operated with crystal monochromators with values of [\Delta\lambda/\lambda] far smaller than what equation (9)[link] would require.

[Figure 2]
Figure 2
The stacking of multiple thinner zone plates can lead to higher optical performance than can be obtained with a thicker single zone plate. On the left (a) is show the focusing efficiency (in terms of integrated energy fraction as a function of radius from the focal spot center) and, as an inset, the focused intensity profile for the three zone-plate design schemes and parameters outlined in Table 1[link]. This is for the case of zone plates separated by a very large distance of [\Delta z] = 1000 µm relative to the focal length of f = 9074 µm for the first, upstream zone plate. The inset shows that the strategy of fixed diameter d gives a higher Rayleigh resolution (smaller radius for the first minimum of the intensity distribution) than the strategies of fixed outermost zone width drN or fixed zone number N. On the right (b) is shown the integrated energy fraction for a single t = 2000 nm-thick zone plate versus four t = 500 nm-thick zone plates separated by [\Delta z] = 50 µm, and designed according to the fixed diameter d strategy. If multiple thinner zone plates can be aligned with sufficient accuracy, they can offer higher overall focusing efficiency (though in this case the separation between the zone plates is so small that they all have essentially the same numerical aperture, so there is no spatial resolution gain).

3. Multiple zone plate exit waves

In near-field zone plate stacking, the optical effect of each zone plate is simply superimposed on the incident wavefield with no interceding propagation-based wavefield evolution. In non-near-field stacking, simulations (Vila-Comamala et al., 2013[Vila-Comamala, J., Wojcik, M., Diaz, A., Guizar-Sicairos, M., Kewish, C. M., Wang, S. & David, C. (2013). J. Synchrotron Rad. 20, 397-404.]) and experiments (Gleber et al., 2014[Gleber, S. C., Wojcik, M., Liu, J., Roehrig, C., Cummings, M., Vila-Comamala, J., Li, K., Lai, B., Shu, D. & Vogt, S. (2014). Opt. Express, 22, 28142-28153.]) have calculated the intensity profile near the focal region. In Fig. 3[link], we show for the first time the nature of the exit wave from the last of a set of stacked zone plates. (This exit wave then converges to produce the focal spot.) When multiple stacked zone plates are used, the exit wave from multiple stacked zone plates evolves towards that of a blazed zone plate (Fig. 1b[link]). Because of this, one can achieve a higher diffraction efficiency with a set of separated stacked zone plates than would be expected simply from the sum of the zone plate thicknesses and equation (1)[link].

[Figure 3]
Figure 3
Phase profile of the exit wave from (top) a single topt = 2.0 µm-thick zone plate of gold for 10 keV X-ray focusing, (middle) four 0.5 µm-thick zone plates, and (bottom) ten 0.2 µm-thick zone plates. In each case the phase of the exit wave from the final downstream zone plate is shown. By using multiple thin zone plates, one can better approximate the phase profile of a blazed zone plate (Fig. 1b[link]).

A staircase approximation to single-optic blazed zone plates has been realized by using multiple overlaid lithography steps to produce a single optical structure with improved focusing efficiency (Krasnoperova et al., 1993[Krasnoperova, A. A., Xiao, J., Cerrina, F., Di Fabrizio, E., Luciani, L., Figliomeni, M., Gentili, M., Yun, W., Lai, B. & Gluskin, E. (1993). J. Vac. Sci. Technol. B, 11, 2588-2591.]; Di Fabrizio et al., 1994[Di Fabrizio, E., Gentili, M., Grella, L., Baciocchi, M., Krasnoperova, A., Cerrina, F., Yun, W., Lai, B. & Gluskin, E. (1994). J. Vac. Sci. Technol. B, 12, 3979-3985.], 1999[Di Fabrizio, E., Romanato, F., Gentili, M., Cabrini, S., Kaulich, B., Susini, J. & Barrett, R. (1999). Nature (London), 401, 895-898.]; Yun et al., 1999[Yun, W., Lai, B., Krasnoperova, A. A., Di Fabrizio, E., Cai, Z., Cerrina, F., Chen, Z., Gentili, M. & Gluskin, E. (1999). Rev. Sci. Instrum. 70, 3537-3541.]). However, if k lithographic overlays are used to produce a zone profile with k stair steps, the finest transverse feature size in the last stair step must be drN/k to achieve a net width drN of the finest outermost half of the blazed structure. In other words, if the finest transverse feature size that a given lithographic process can produce is a, then the finest zone half period is ka rather than having drN = a. In this case the increase in efficiency of using k steps to produce a staircase approximation of a blazed zone plate comes at a cost in achievable spatial resolution.

Separated stacked zone plates can avoid this undesirable tradeoff. In Fig. 3[link], we show the phase of the wavefield exiting the final downstream zone plate for the case of a single topt = 2000 nm-thick [equation (4)[link]] zone plate of gold for use at 10 keV for which equation (1)[link] gives a diffraction efficiency of [\varepsilon_{1}] = 32.7%, as well as the exit waves for four zone plates each with 500 nm thickness, and ten zone plates each with 200 nm thickness (in all cases the separation distance was [\Delta z] = 10 µm). The wavefield propagation through each individual zone plate was calculated using a multislice approach (Cowley & Moodie, 1957[Cowley, J. M. & Moodie, A. F. (1957). Acta Cryst. 10, 609-619.]; Li et al., 2017a[Li, K., Wojcik, M. & Jacobsen, C. (2017a). Opt. Express, 25, 1831-1846.]). As was noted, the ten zone plate case produces a last-zone-plate exit wave strongly resembling what one would have from a blazed zone plate.

In order to explore this further, we first consider the case of the number of zone plates to be used and the resulting diffraction efficiency. While the optimum thickness for a single zone plate of gold at 10 keV is topt = 2.0 µm, in Fig. 4[link] we consider cumulative zone plate thicknesses as high as t = 4.0 µm while in fact using multiple zone plates with individual thicknesses ti ranging from ti = 0.1 µm (so that nzp = 40 such zone plates would have an accumulated thickness of t = 4.0 µm if they had the same design parameters) to ti = 2.0 µm (so that only nzp = 2 zone plates would be stacked). In all cases, a separation distance of [\Delta z] = 10 µm was used. As this figure shows, one can obtain a diffraction efficiency of [\varepsilon] = 66% if one uses nzp = 30 zone plates that are each only ti = 0.1 µm thick at [\Delta z] = 10 µm spacing, where each is designed according to the fixed diameter d strategy described in §2[link]. Even if fewer zone plates are used with a cumulative thickness limited to topt = 2.0 µm, one still sees gains over single zone plates: for example, nzp = 4 zone plates each with ti = 0.5 µm give an efficiency of [\varepsilon] = 41.5% while if one uses nzp = 10 zone plates with ti = 0.2 µm the efficiency is [\varepsilon] = 48.9%.

[Figure 4]
Figure 4
While there might be practical limitations to the number of zone plates nzp that can be stacked together, one can obtain gains in first-order diffraction efficiency [\varepsilon_{1}] that go well beyond the simple thin zone plate expression of equation (1)[link]. In (a) we show the efficiency as a function of individual zone plate thickness ti and cumulative thickness t, where nzp = t/ti zone plates are used with with a separation of [\Delta z] = 10 µm (for d = 45 µm, and drN = 25 nm for the first zone plate at 10 keV). A single gold zone plate with the optimum thickness topt = 2.0 µm would give [\varepsilon_{1}] = 32.7%, whereas much higher efficiencies can be obtained by using many more zone plates with slightly higher cumulative thickness. In (b) we show how the stacking of nzp = 8 zone plates, each with a thickness ti = 0.5 µm, leads to differences in diffraction efficiency as one changes the separation distance [\Delta z] between zone plates. Smaller separation distances [\Delta z] are preferable but might be impractical, but even with larger separation distances like [\Delta z] = 1000 µm one can still obtain an efficiency of [\varepsilon_{1}] = 36% if nzp = 5 zone plates are used. All calculations were for gold zone plates at 10 keV.

Fig. 4(a)[link] used a constant separation distance of [\Delta z] = 10 µm between zone plates, which is in practice a very small separation distance. Fig. 4(b)[link] shows how the performance of multiple zone plates (each with ti = 500 nm thickness) changes as one increases the separation distance [\Delta z]. As can be seen, smaller separation distances are preferred, but even with [\Delta z] = 100 µm one can obtain a first-order diffraction efficiency of [\varepsilon_{1}] = 44.8% by using nzp = 5 zone plates.

4. The Talbot effect and zone plate spacing

The Talbot effect (Talbot, 1836[Talbot, H. F. (1836). Philos. Mag. Ser. 3, 9, 401-407.]; Lord, 1881[Lord, R. (1881). Philos. Mag. Ser. 5, 11, 196-205.]) involves the replication of a transmission grating pattern of period a at a Talbot distance

[z_{\rm Talbot} = {{2a^{2}}/{\lambda}} \eqno(10)]

when zero and first diffraction orders constructively interfere (Fig. 5[link]). This suggests that there might be an optimum separation distance [\Delta z] for stacked zone plate. Because the local grating period in a Fresnel zone plate varies constantly with radius, it is less clear whether the Talbot effect should apply based on the period 2drN of the finest zone width, or on the period 4drN of the zones at half the radius, or whether it is `washed out' by the variation in zone width.

[Figure 5]
Figure 5
Illustration of the Talbot effect. When a periodic diffraction grating is illuminated by a plane wave, the image of the grating is repeated at a Talbot distance of zTalbot = [2a^{2}/\lambda] [equation (10)[link]] where a is the period of the diffraction grating. For a grating period of a = 100 nm, and [\lambda] = 0.124 nm (corresponding to 10 keV X-rays), the Talbot distance is zTalbot = 161 µm. The grating here was assumed to be fully absorptive.

While Fig. 4(b)[link] showed the effect of only a few different separation distances [\Delta z], in Fig. 6[link] we show the effect of a much larger number of more finely varied separation distances. In this figure, for each value of individual zone plate thickness ti and separation distance [\Delta z], the optimum number nzp of individual zone plates was chosen as is shown in Fig. 4(a)[link] and the average value of nzp is shown for each thickness ti. Clearly, we see maxima and minima of efficiencies with respect to stacking separations, and a dependence on outermost zone width drN.

[Figure 6]
Figure 6
Diffraction efficiency [\varepsilon_{1}] versus separation distance [\Delta z] for different thicknesses ti of individual zone plates, and for two different values of outermost zone width: drN = 20 nm (a) and drN = 30 nm (b). For each individual zone thickness ti and separation distance [\Delta z], the number of stacked zone plates nzp was chosen to give maximum efficiency, as shown in Fig. 4(b)[link], and the average value of nzp corresponding to a particular value of ti is indicated. As can be seen, there is a pattern of maxima and minima in the efficiences as a function of separation distance [\Delta z], with the first two maxima denoted by zmax1 and zmax2, and the first two minima denoted by zmin1 and zmin2. These maxima and minima are compared with the Talbot distance [equation (10)[link]] for the outermost zones in Fig. 7[link].

In order to better compare the separation distances leading to the first two maxima (zmax1,zmax2) and minima (zmin1,zmin2) in Fig. 6[link], in Fig. 7[link] we show these extrema both as a function of varying the outermost zone width drN in Fig. 7(a)[link], and the zone plate diameter d in Fig. 7(b)[link]. Obviously the efficiency maxima and minima depend on outermost zone width drN rather than diameter d. In Fig. 7(a)[link], we also indicate the Talbot distance zTalbot of a grating with a period 2drN corresponding to the outermost zone width. While the positions of the maxima and minima show the expected scaling with (drN)2, the separation distance zmax1 corresponding to the first efficiency maximum is about one quarter of the value [2(2\,{\rm{d}}r_{N})^{2}/\lambda] that one would predict from equation (10)[link] based on the outermost zone width. As shown in Fig. 5[link], at this distance a constant-period grating shows an interference pattern at half the period of the grating, and with a contrast inversion.

[Figure 7]
Figure 7
Positions of the efficiency maxima (zmax1,zmax2) and minima (zmin1,zmin2) shown in Fig. 6[link] as a function of varying outermost zone width drN (a) or diameter d (b). This was done for an individual zone plate thickness of ti = 0.9 µm. Clearly the separation distances [\Delta z] show maxima and minima that scale with outermost zone width drN rather than diameter d. Also shown on the left is the Talbot distance zTalbot based on equation (10)[link] for a grating with a period a = 2drN determined by the outermost zone width. The efficiency maxima and minima scale with drN, but the ideal separation distance [\Delta z] corresponding to zmax1 is at about one-quarter of the distance [2(2\,{\rm{d}}r_{N})^{2}/\lambda].

5. High diffraction orders and complementary zone plates

In nanofabrication using electron beam lithography, transverse spreading of the electron beam in the photoresist (the proximity effect) can complicate the fabrication of dense narrow-linewidth structures such as the zones in a Fresnel zone plate. For this reason, a variety of interlacing approaches have been used in which every other zone is written in one operation, with a subsequent identical operation used to write the alternating zones either on the same side of a thin window (Chao et al., 2005[Chao, W., Harteneck, B. D., Liddle, J. A., Anderson, E. H. & Attwood, D. T. (2005). Nature (London), 435, 1210-1213.]) as shown in Fig. 8(b)[link], or on the opposite side (Mohacsi et al., 2017[Mohacsi, I., Vartiainen, I., Rösner, B., Guizar-Sicairos, M., Guzenko, V. A., McNulty, I., Winarski, R., Holt, M. V. & David, C. (2017). Sci. Rep. 7, 43624.]) as shown in Fig. 8(c)[link]. Another way to reduce the limitations of the proximity effect is to write narrower zones in a low-density template, and use atomic layer deposition (ALD) to deposit high-density material on these templates in a process known as zone doubling (Jefimovs et al., 2007[Jefimovs, K., Vila-Comamala, J., Pilvi, T., Raabe, J., Ritala, M. & David, C. (2007). Phys. Rev. Lett. 99, 264801.]). Yet another approach is to consider the fabrication of zone plates with line:space ratios other than 1:1 where the separation distance between written structures can be increased (again reducing the proximity effect in electron beam lithography), while working in higher diffraction orders (Schneider, 1997[Schneider, G. (1997). Appl. Phys. Lett. 71, 2242-2244.]).

[Figure 8]
Figure 8
A normal Fresnel zone plate with 1:1 line:space ratio (a) can be constructed by interlacing two fabrication processes, either on the same side of a thin window (Chao et al., 2005[Chao, W., Harteneck, B. D., Liddle, J. A., Anderson, E. H. & Attwood, D. T. (2005). Nature (London), 435, 1210-1213.]) (b) or on opposite sides (Mohacsi et al., 2017[Mohacsi, I., Vartiainen, I., Rösner, B., Guizar-Sicairos, M., Guzenko, V. A., McNulty, I., Winarski, R., Holt, M. V. & David, C. (2017). Sci. Rep. 7, 43624.]) (c). Both of those interlaced processes reduce the limitations produced by the proximity effect in electron beam lithography in the separate fabrication processes. The proximity effect is reduced further if one fabricates zones with a line:space ratio of 1:3 and uses them in the second diffraction order. One can also use complementary zone plates with an opposite pattern of material-filled/open zones. That leads to several options in zone plate stacking: stacking with 1:3 line:space ratio with a regular (d) or complementary (e) second zone plate, or with 1:1 line:space ratio with a regular (f) or complementary second zone plate. These various combinations give different properties for focusing efficiency and focal spot sidelobes, as shown in Fig. 9[link].

Inspired by these approaches, in Fig. 8[link] we consider several options for zone plate stacking:

(i) The first of these is the use of line:space ratios with values such as 1:3, giving more space between lithographically patterned zones and thereby reducing the limitations set by the proximity effect. With a 1:1 zone plate, the outermost zone period is pN = 2drN and the Rayleigh resolution is [\delta_{\rm r}] = 1.22 drN/m. With other values of the line:space ratio, it is better to base the Rayleigh resolution expression using the outermost zone period pN, giving

[\delta_{\rm r} = 0.61\,{{p_{N}}/{m}}. \eqno(11)]

When the line:space ratio in a grating is changed from 1:1 to other values, the energy distribution into various diffractive orders is modified. For example, a 1:3 zone plate operated in the m = 2 diffraction order can in principle have twice the spatial resolution for a given period pN as shown in equation (11)[link], and there can be specific thicknesses and line:space ratios which deliver high focusing efficiency into the m = 2 order as calculated using coupled wave theory (Schneider, 1997[Schneider, G. (1997). Appl. Phys. Lett. 71, 2242-2244.]). By working in the second diffraction order, one obtains a factor of two improvement in spatial resolution compared with the minimum zone width.

(ii) The second of these is the use of complementary zone plates. In the normal case for a Fresnel zone plate, the zeroth or central zone is filled with material up to a radius r1 as given by

[r_{k}^{\,2} \simeq k\lambda f + \left({{k\lambda}/{2}}\right)^{2}, \eqno(12)]

after which one alternates between open and material-filled zones such that the next material-filled zone is bounded by r2 and r3. However, in a complementary zone plate the central zone is open and the first material-filled zone is bounded by r1 and r2. Complementary zone plates do not by themselves provide any reduction in the proximity effect, but they can be used with any line:space ratio including 1:1 or 1:3.

Variation of the line:space ratio and the use of regular or complementary zone plates give us additional options in stacked zone plate design. In addition, when using separated stacked zone plates rather than the interlacing schemes of Figs. 8(b) or 8(c)[link], one gains the ability to use processes that are difficult to interlace on one window. One of these is metal-assisted chemical etching (MACE) to produce extremely high aspect ratio zone-doubling template structures for ALD (Chang & Sakdinawat, 2014[Chang, C. & Sakdinawat, A. (2014). Nat. Commun. 5, 4243.]; Li et al., 2017b[Li, K., Wojcik, M. J., Divan, R., Ocola, L. E., Shi, B., Rosenmann, D. & Jacobsen, C. (2017b). J. Vac. Sci. Technol. B, 35, 06G901.]).

We consider the second diffraction order (m = 2) focusing properties of zone plates with differing line:space ratio in Fig. 9[link] where we also consider the option of having either a regular or complementary second zone plate. These simulations were carried out with a thickness of t = 1 µm of Au and an incident X-ray energy of 10 keV. In Fig. 9(a)[link], we show the radial focal profiles, and radially integrated intensity, as a function of radius from the optical axis in the case where the outermost zone period is pN = 100 nm and the separation is [\Delta z] = 50 µm. As can be seen, for second-order focusing a 1:3 line:space ratio is preferred over a 1:1 line:space ratio, as expected (for a thin zone plate, a 1:1 line:space ratio would give zero efficiency for the second-order focus). Having the second zone plate being a regular zone plate gives higher focusing efficiency than using a complementary zone plate.

[Figure 9]
Figure 9
Stacking of two zone plates with 100 nm outermost zone period, each with ti = 1 µm thickness, at 10 keV photon energy. Using the four different stacking schemes shown in Fig. 8[link], in (a) we show both the radial intensity profile and also the radially integrated energy for m = 2 second diffraction order focusing. The 1:3 line:space approach with the second zone plate being a complementary zone plate has a unique property of having very little energy in sidelobes around the central focus spot. In (b) we show the normalized focus intensity for 1:3 line:space stacking with regular and complementary second zone plate as a function of separation distance [\Delta z], demonstrating a crossover between which approach is preferred at half of [\Delta z_{\rm{c}}] of equation (13)[link]. In (c) we show the focal spot intensity as the line:space ratio is adjusted in both the upstream and (regular) downstream zone plate; the optimum line:space ratio for a variety of separation distances [\Delta z] is shown in (d).

One very interesting feature of the complementary 1:3 line:space ratio case is that there is very little increase in light in `sidelobes' outside the central focus spot (though the central focus spot is slightly widened). This can be of advantage in methods such as the mapping of trace elements by X-ray fluorescence, since a focal probe without sidelobes will allow for better quantitation of the elemental content within the central focus spot with little or no signal contributed from other nearby positions.

When working in the first diffraction order, downstream stacked zone plates will be of the same type as the first one (that is, regular rather than complementary zone plates) with their parameters modified with separation distance as described in §2[link]. However, when working in the second diffraction order, the wavefield converging from the first zone plate will converge at twice the normal angle, or [\theta] = [2\lambda/p_{N}], which when multiplied by the separation distance [\Delta z] gives a reduction of radius for a given zone number of [2\lambda\Delta z/p_{N}] rather than [1\lambda \Delta z/p_{N}]. If one sets the extra radius reduction of [1\lambda\Delta z_{\rm{c}}/p_{N}] equal to one zone period pN, one finds

[{{\lambda \Delta z_{\rm{c}}}/{p_{N}}} = p_{N}, \qquad \Delta z_{\rm{c}} = {{p_{N}^{2}}/{\lambda}}. \eqno(13)]

That is, at a distance of [\Delta z_{\rm{c}}] the second zone plate will work with its zones shifted by one period, and at half that distance one will have a transition to requiring that the second zone plate be a complementary one rather than a regular one. For pN = 100 nm and [\lambda] = 0.124 nm corresponding to 10 keV, the `matched' distance is [\Delta z_{\rm{c}}] = 81 µm and the transition to a complementary zone plate should occur at half that distance or about [\Delta z_{\rm{c}}/2] = 40 µm. This effect is shown in Fig. 9(b)[link], where when using stacked 1:3 line:space ratio zone plates in the second diffraction order one finds that a complementary zone plate is preferred at distances smaller than [\Delta z_{\rm{c}}/2], and at [\Delta z_{\rm{c}}/2] and above there is a change to preferring a regular zone plate.

For two zone plates stacked in close proximity (such as interlaced zone plates) operating in the second diffraction order, a line:space ratio of 1:3 should give near-optimum diffraction efficiency. However, the optimum line:space ratio can be different when two zone plates become more separated. We therefore undertook simulations where the line:space ratio of both the first and second zone plates was adjusted. The results for a fixed separation distance of [\Delta z] = 50 µm are shown in Fig. 9(c)[link], which indicates that a line:space ratio of about 1:2.7 is preferred to 1:3 for both zone plates in regular stacking. However, given that complementary zone plates can be preferred at certain distances as shown in Fig. 9(b)[link] and as discussed above, in Fig. 9(d)[link] we show the focus intensity for the optimum line:space ratio, and also the value of that optimum line:space ratio, for two stacked zone plates as a function of separation distance [\Delta z].

The calculations shown in Fig. 9[link] were for the case of a fixed zone thickness of t = 1 µm. In Fig. 10[link], we show how the optimal line:space ratio depends on both the thickness ti of the two individual zone plates, and the stacking separation distance [\Delta z]. At a zone plate thickness of ti = 0.5 µm, the differences between having the second zone plate being regular or complementary are not so significant, whereas they are quite noticeable with ti = 2 µm, which corresponds to a π phase shift. This makes it clear that the differences between using a regular or a complementary zone plate for the second zone plate are volume diffraction effects.

[Figure 10]
Figure 10
Optimum line:space ratio (a) and resulting relative focusing intensity (b) for m = 2 second-order focusing as a function of both zone thickness ti and separation distance [\Delta z]. The differences between using a regular or a complementary zone plate for the second optic become larger when thickness ti approaches 2 µm which corresponds to a π phase shift.

6. Refocusing zone plates

In the simulations shown above, only the zeroth or positive focal orders are used from upstream zone plates. However, significant energy goes into negative diffraction orders, which diverge from a virtual focus located upstream. We now consider schemes to recapture a fraction of this energy using a stacked refocusing zone plate. The idea is shown schematically in Fig. 11(a)[link]. The refocusing zone plate can be designed to operate in mr = 1 or first diffraction order, but this requires a finer outermost zone width drN in the refocusing zone plate than is used in the first or second (stacked) zone plate. Therefore another option to consider is the use of mr = 3 or third-order diffraction by the refocusing zone plate, so that the minimum zone width drN in the refocusing zone plate is larger than the minimum zone width drN in the conventional and stacked zone plate. For the refocusing zone plate, the usual expression for conventional zone plate zone radii rk of equation (12)[link] is replaced with

[r_{\ell}^{\,2} = \ell m_{r}\lambda f + \left( {{ \ell m_{r}\lambda }\over{ 2}} \right)^2 \left[1+{{M}\over{(1+M)^2}}\right], \eqno(14)]

where l indexes the zones in the refocusing zone plate, and M is the magnification of the source to its image.

[Figure 11]
Figure 11
Refocusing zone plates can recapture some of the m = −1-order focus light from a conventional zone plate. This is shown schematically in (a), where one can produce a combined optic with a stacked zone plate in the inner diameter and a refocusing zone plate operating in either mr = 1 or first diffraction order, or mr = 3 or third diffraction order. The effect on the focus profile and integrated energy as a function of radius is shown in (b), for the cases of a conventional zone plate alone (case C), or with the addition of a refocusing zone plate operating in first diffraction order (case CR1), or with a refocusing zone plate operating in third diffraction order (case CR3). Both refocusing zone plates offer an increase in focal efficiency, with the CR1 case also offering an improvement in spatial resolution. However, in the CR1 case the refocusing zone plate must have finer zone width drN than the conventional zone plate, and usually the conventional zone plate is fabricated out to the limits of what can be achieved in nanolithography; in the CR3 case, the finest zone width drN is the same for the conventional (C) and third-order refocusing (R3) zone plates. The parameters for the zone plates used for the calculation of focal intensities (b) are given in Table 2[link].

In order to understand the potential improvements that might be provided by using a refocusing zone plate, we first calculated three cases where we did not include a stacked zone plate: a conventional zone plate with central stop [case C in Fig. 11(b)[link]], the conventional zone plate plus a refocusing zone plate operated with mr = 1 or first diffraction order [case CR1 in Fig. 11(b)[link]], and a conventional zone plate plus a refocusing zone plate operated with mr = 3 or third diffraction order [case CR3 in Fig. 11(b)[link]]. The parameters of the zone plates considered can be found in Table 2[link]. This figure demonstrates that the refocusing zone plate can add substantially to the conventional zone plate's focusing efficiency.

Table 2
Zone plate parameters used for the calculation shown in Fig. 11(b)[link]

In the case of a refocusing zone plate operating in first diffraction order, one can see that a much smaller outermost zone width drN is required than in the conventional zone plate. Because nanolithography processes are often limited in their achievable aspect ratio ti/drN, the thickness of R1 was decreased to maintain a limiting aspect ratio of 20.

Zone plate Label d (µm) drN (nm) ti (nm) f (µm) [\Delta z] (µm)
Refocusing zone plate (first order) R1 20–60 8.3 167 4032 3024
Refocusing zone plate (third order) R3 20–60 25 500 12096 3024
Conventional zone plate C 15–45 25 500 9074  

Having seen the effect of a refocusing zone plate alone in Fig. 11(b)[link], we add a stacked zone plate in the position indicated in Fig. 11(a)[link] to give the results shown in Fig. 12[link]. In this case, a comparison was made between a conventional zone plate (C) with and without a stacked zone plate (S), and with and without a third-order refocusing zone plate (R3), using the parameters shown in Table 3[link]. As can be seen, the re­focusing zone plate adds to the intensity in the first-order focus, though the stacked zone plate S plays a more important role than the refocusing zone plate R3. We note that the stacked S and refocusing R3 zone plates can be fabricated on the same window, so the refocusing zone plate adds little additional complexity. Also, as the separation distance [\Delta z] between the conventional zone plate (C) and stacked/refocusing zone plate (SR3) is increased, the area of the stacked zone plate will decrease while the area of the refocusing zone plate will increase and the improvement from using a refocusing zone plate should also increase. Finally, the use of mr = 3 third-order diffraction in the refocusing zone plate R3 leads to a 1/mr2 sharpening of the axial intensity profile as shown in Fig. 12(b)[link].

Table 3
Zone plate parameters assumed for Fig. 12[link]

  Label D (µm) [\Delta r_N] (nm) t (nm) f (µm)
Conventional zone plate C 15–45 25 500 9074
Stacking zone plate S 10–30 25 500 6049
Refocusing zone plate R3 30–60 25 500 12096
[Figure 12]
Figure 12
Effect of using both stacked and refocusing zone plates. Four combinations were compared: a conventional zone plate alone (C), or optionally with a stacked zone plate (S), or optionally with a third diffraction order refocusing zone plate (R3). This gives combinations C, CS, CR3 and CSR3 as indicated. On the left (a) is shown the focused intensity profile and radial integral of energy, while on the right (b) is shown the set of axial intensity profiles. Adding a refocusing zone plate provides some increase in focused intensity, but only over a narrow depth of focus range reduced by a factor of 1/m2 due to the presence of the third diffraction order refocusing zone plate (R3). The parameters for the individual zone plates are shown in Table 3[link].

7. Conclusion

Following the introduction of the concept of stacking multiple zone plates at beyond-proximity distances (Vila-Comamala et al., 2013[Vila-Comamala, J., Wojcik, M., Diaz, A., Guizar-Sicairos, M., Kewish, C. M., Wang, S. & David, C. (2013). J. Synchrotron Rad. 20, 397-404.]), we have considered here a variety of design options. Using multislice propagation (Cowley & Moodie, 1957[Cowley, J. M. & Moodie, A. F. (1957). Acta Cryst. 10, 609-619.]; Li et al., 2017a[Li, K., Wojcik, M. & Jacobsen, C. (2017a). Opt. Express, 25, 1831-1846.]) to handle the case of wavefield propagation within thicker zone plates, we studied the effects of stacked zone plate parameter design schemes and choice of separation distances. In the supporting information, we also follow prior work on understanding the effects of alignment errors (Vila-Comamala et al., 2013[Vila-Comamala, J., Wojcik, M., Diaz, A., Guizar-Sicairos, M., Kewish, C. M., Wang, S. & David, C. (2013). J. Synchrotron Rad. 20, 397-404.]; Gleber et al., 2014[Gleber, S. C., Wojcik, M., Liu, J., Roehrig, C., Cummings, M., Vila-Comamala, J., Li, K., Lai, B., Shu, D. & Vogt, S. (2014). Opt. Express, 22, 28142-28153.]) by providing a more detailed look at the effects on the focal spot.

Combining multiple zone plates can lead to higher focusing efficiency and focal spots with different characteristics (such as reduced sidelobes), but the design details matter. One can also understand the potential improvements by realizing that the stacking of multiple planar zone plates leads one toward the situation of a volume grating. Separate mounting and aligning of up to five stacked zone plates has already been demonstrated (Gleber et al., 2014[Gleber, S. C., Wojcik, M., Liu, J., Roehrig, C., Cummings, M., Vila-Comamala, J., Li, K., Lai, B., Shu, D. & Vogt, S. (2014). Opt. Express, 22, 28142-28153.]), and this approach with mechanical adjustment has the advantage of allowing one to tune the incident photon energy and then adjust the separation distance between zone plates as required. For single-wavelength operation, one can also use monolithic mounting approaches (Feng et al., 2007[Feng, Y., Feser, M., Lyon, A., Rishton, S., Zeng, X., Chen, S., Sassolini, S. & Yun, W. (2007). J. Vac. Sci. Technol. B, 25, 2004.]) where multiple zone plates are pre-aligned and fixed in place prior to use. In general, more zone plates are better, but the details matter!

8. Related literature

The following references, not cited in the main body of the paper, have been cited in the supporting information: Pratsch et al. (2014[Pratsch, C., Rehbein, S., Werner, S. & Schneider, G. (2014). Opt. Express, 22, 30482.]); Simpson & Michette (1983[Simpson, M. J. & Michette, A. G. (1983). Opt. Acta, 30, 1455-1462.]).

Supporting information


Footnotes

Present address: SLAC, Menlo Park, CA 94025, USA.

Acknowledgements

We thank Michael Wojcik of the Advanced Photon Source at Argonne for many helpful discussions. We thank the Office of Science, Department of Energy, for support for this work at the Advanced Photon Source at Argonne National Laboratory.

Funding information

Funding for this research was provided by: Office of Science, United States Department of Energy (contract No. DE-AC02-06CH11357).

References

First citationAristov, V. V., Isoyan, A., Kohn, V., Kuyumchyan, A., Shulakov, E., Snigirev, A. A. & Snigireva, I. (2007). Nucl. Instrum. Methods Phys. Res. A, 575, 238–241.  Web of Science CrossRef Google Scholar
First citationAttwood, D. & Sakdinawat, A. (2017). X-rays and Extreme Ultraviolet Radiation, 2nd ed. Cambridge University Press.  Google Scholar
First citationChang, C. & Sakdinawat, A. (2014). Nat. Commun. 5, 4243.  Web of Science CrossRef PubMed Google Scholar
First citationChao, W., Harteneck, B. D., Liddle, J. A., Anderson, E. H. & Attwood, D. T. (2005). Nature (London), 435, 1210–1213.  Web of Science CrossRef PubMed CAS Google Scholar
First citationCowley, J. M. & Moodie, A. F. (1957). Acta Cryst. 10, 609–619.  CrossRef IUCr Journals Web of Science Google Scholar
First citationDi Fabrizio, E., Gentili, M., Grella, L., Baciocchi, M., Krasnoperova, A., Cerrina, F., Yun, W., Lai, B. & Gluskin, E. (1994). J. Vac. Sci. Technol. B, 12, 3979–3985.  CrossRef Web of Science Google Scholar
First citationDi Fabrizio, E., Romanato, F., Gentili, M., Cabrini, S., Kaulich, B., Susini, J. & Barrett, R. (1999). Nature (London), 401, 895–898.  Web of Science CrossRef CAS Google Scholar
First citationFeng, Y., Feser, M., Lyon, A., Rishton, S., Zeng, X., Chen, S., Sassolini, S. & Yun, W. (2007). J. Vac. Sci. Technol. B, 25, 2004.  Web of Science CrossRef Google Scholar
First citationGleber, S. C., Wojcik, M., Liu, J., Roehrig, C., Cummings, M., Vila-Comamala, J., Li, K., Lai, B., Shu, D. & Vogt, S. (2014). Opt. Express, 22, 28142–28153.  Web of Science CrossRef Google Scholar
First citationGoodman, J. W. (2005). Introduction to Fourier Optics. Greenwood Village: Roberts and Company Publishers.  Google Scholar
First citationHenke, B. L., Gullikson, E. M. & Davis, J. C. (1993). At. Data Nucl. Data Tables, 54, 181–342.  CrossRef CAS Web of Science Google Scholar
First citationJefimovs, K., Vila-Comamala, J., Pilvi, T., Raabe, J., Ritala, M. & David, C. (2007). Phys. Rev. Lett. 99, 264801.  Web of Science CrossRef PubMed Google Scholar
First citationKagoshima, Y., Takano, H., Koyama, T., Tsusaka, Y. & Saikubo, A. (2011). Jpn. J. Appl. Phys. 50, 022503.  CrossRef Google Scholar
First citationKirz, J. (1974). J. Opt. Soc. Am. 64, 301–309.  CrossRef CAS Web of Science Google Scholar
First citationKogelnik, H. (1969). Bell Syst. Tech. J. 48, 2909–2947.  CrossRef Web of Science Google Scholar
First citationKrasnoperova, A. A., Xiao, J., Cerrina, F., Di Fabrizio, E., Luciani, L., Figliomeni, M., Gentili, M., Yun, W., Lai, B. & Gluskin, E. (1993). J. Vac. Sci. Technol. B, 11, 2588–2591.  CrossRef Web of Science Google Scholar
First citationLi, K., Wojcik, M. J., Divan, R., Ocola, L. E., Shi, B., Rosenmann, D. & Jacobsen, C. (2017b). J. Vac. Sci. Technol. B, 35, 06G901.  Web of Science CrossRef Google Scholar
First citationLi, K., Wojcik, M. & Jacobsen, C. (2017a). Opt. Express, 25, 1831–1846.  Web of Science CrossRef Google Scholar
First citationLord, R. (1881). Philos. Mag. Ser. 5, 11, 196–205.  Google Scholar
First citationMaser, J., Lai, B. P., Yun, W., Shastri, S. D., Cai, Z., Rodrigues, W., Xu, S. & Trackhtenberg, E. (2002). Proc. SPIE, 4783, 74–81.  CrossRef Google Scholar
First citationMaser, J. & Schmahl, G. (1992). Opt. Commun. 89, 355–362.  CrossRef Web of Science Google Scholar
First citationMohacsi, I., Karvinen, P., Vartiainen, I., Guzenko, V. A., Somogyi, A., Kewish, C. M., Mercere, P. & David, C. (2014). J. Synchrotron Rad. 21, 497–501.  Web of Science CrossRef CAS IUCr Journals Google Scholar
First citationMohacsi, I., Vartiainen, I., Rösner, B., Guizar-Sicairos, M., Guzenko, V. A., McNulty, I., Winarski, R., Holt, M. V. & David, C. (2017). Sci. Rep. 7, 43624.  Web of Science CrossRef Google Scholar
First citationPennington, K. S. & Lin, L. H. (1965). Appl. Phys. Lett. 7, 56–57.  CrossRef Web of Science Google Scholar
First citationPratsch, C., Rehbein, S., Werner, S. & Schneider, G. (2014). Opt. Express, 22, 30482.  Web of Science CrossRef Google Scholar
First citationRehbein, S., Lyon, A., Leung, R., Feser, M. & Schneider, G. (2015). Opt. Express, 23, 11063–11072.  Web of Science CrossRef Google Scholar
First citationSakdinawat, A. & Attwood, D. (2010). Nat. Photon. 4, 840–848.  Web of Science CrossRef CAS Google Scholar
First citationSchneider, G. (1997). Appl. Phys. Lett. 71, 2242–2244.  CrossRef CAS Web of Science Google Scholar
First citationSchneider, G., Rehbein, S. & Werner, S. (2008). Modern Developments in X-ray and Neutron Optics, edited by A. Erko, M. Idir, T. Krist and A. G. Michette, pp. 137–171. Springer.  Google Scholar
First citationSchneider, G., Schliebe, T. & Aschoff, H. (1995). J. Vac. Sci. Technol. B, 13, 2809–2812.  CrossRef Web of Science Google Scholar
First citationShastri, S. D., Maser, J. M., Lai, B. & Tys, J. (2001). Opt. Commun. 197, 9–14.  Web of Science CrossRef CAS Google Scholar
First citationSimpson, M. J. & Michette, A. G. (1983). Opt. Acta, 30, 1455–1462.  CrossRef Web of Science Google Scholar
First citationSnigireva, I., Snigirev, A., Kohn, V., Yunkin, V., Grigoriev, M., Kuznetsov, S., Vaughan, G. & Di Michiel, M. (2007). Phys. Status Solidi A, 204, 2817–2823.  Web of Science CrossRef CAS Google Scholar
First citationSpector, S., Jacobsen, C. & Tennant, D. (1997). J. Vac. Sci. Technol. B, 15, 2872–2876.  Web of Science CrossRef CAS Google Scholar
First citationTalbot, H. F. (1836). Philos. Mag. Ser. 3, 9, 401–407.  Google Scholar
First citationThieme, J. (1988). X-ray Microscopy II, edited by D. Sayre, M. R. Howells, J. Kirz and H. Rarback, Vol. 56 of Springer Series in Optical Sciences, pp. 70–79. Berlin: Springer-Verlag.  Google Scholar
First citationVila-Comamala, J., Wojcik, M., Diaz, A., Guizar-Sicairos, M., Kewish, C. M., Wang, S. & David, C. (2013). J. Synchrotron Rad. 20, 397–404.  Web of Science CrossRef IUCr Journals Google Scholar
First citationWang, Y., Jacobsen, C., Maser, J. & Osanna, A. (2000). J. Microsc. 197, 80–93.  CrossRef PubMed CAS Google Scholar
First citationWerner, S., Rehbein, S., Guttmann, P. & Schneider, G. (2014). Nano Res. 7, 528–535.  Web of Science CrossRef Google Scholar
First citationYun, W., Lai, B., Krasnoperova, A. A., Di Fabrizio, E., Cai, Z., Cerrina, F., Chen, Z., Gentili, M. & Gluskin, E. (1999). Rev. Sci. Instrum. 70, 3537–3541.  Web of Science CrossRef Google Scholar

This is an open-access article distributed under the terms of the Creative Commons Attribution (CC-BY) Licence, which permits unrestricted use, distribution, and reproduction in any medium, provided the original authors and source are cited.

Journal logoJOURNAL OF
SYNCHROTRON
RADIATION
ISSN: 1600-5775
Follow J. Synchrotron Rad.
Sign up for e-alerts
Follow J. Synchrotron Rad. on Twitter
Follow us on facebook
Sign up for RSS feeds